lps200-m series 250 watts total power: 125 - 250 watts input voltage: 90 - 264 vac # of outputs: single special features ? medical and ite safeties ? active power factor correction ? 3 x 5 footprint ? less than 1u high ? en61000-3-2 compliant ? remote sense ? power fail ? adjustable main output ? built-in class b emi flter ? overvoltage protection ? overload protection ? thermal overload protection ? isolated 12 v fan output ? lpx200 enclosure kit available ? rohs compliant safety ? tuv 60950, 60601-1 ? ul 60950, 60601-1 ? culus 60950, 60601-1 ? cb certifcate & report ? ce mark (lvd) electrical specifcations input input ra nge 90 - 264 vac; 120 - 300 vdc frequency 47 - 63 hz inrush current 50 a max., cold start @ 25 c effciency 86% typical at full load emi/rfi fcc class b conducted; cispr22 class b conducted; en55022 class b conducted; vde0878pt3 class b conducted power factor 0.99 typical safety ground leakage current 275 a @ 50/60 hz, 264 vac input output maximum power 125 w for convection (100 w for lps202-m); 250 w (200 w for lps202-m) with 30cfm forced air adjustment range 10% minimum on the main outputs fan output 12 v @ 0.5 a convection, @ 1 a forced air isolated, 10% hold-up time 16 ms @ 250 w load, 120 vac input overload protection short circuit protection on all outputs. case overload protected @ 110 - 160% above rating overvoltage protection 15 - 50% above nominal output logical control power failure open collector logic signal goes high 100 - 500 msec after main output; it goes low at least 6 msec before loss of regulation remote sense compensates for 0.5 v lead drop min. will operate without remote sense connected. reverse connection protected. data sheet power
environmental specifcations operating temperature 0 c to 50 c ambient derate each output as 2.5% per degree from 50 to 70 c. -20 c start up storage temperature -40 c to +85 c electromagnetic susceptibility designed to meet en61000-4; -2, -3, -4, -5, -6, -8, -11 level 3 humidity operating; non-condensing 10% to 95% rh vibration iec68-2-6 to the levels of iec721-3-2 mtbf calculated 1 million hours at full load and 25 c ambient conditions. 230 vac input, bellcore pin assignments connector lps200-m sk1 pin 1 neutral pin 3 line sk2 tb-1 common tb-2 main output sk3 pin 1 +v1 remote sense pin 2 -v1 remote sense pin 3 n/c pin 4 n/c pin 5 +power fail pin 6 common pin 7 n/c pin 8 common pin 9 +12 v fan pin 10 +12 fan return (isolated) mating connectors ac input (sk1) molex 09-50-8031 (connector) pins: 08-52-0072 ac ground molex 01-90020001 dc output (sk2) molex 19141-0058/0063 or 19099-0044/0048 spade lug based on cable ampacity/awg control sense (sk3) molex 90142-0010 (usa) pins: 90119-2110 or amp: 87977-3 pins: 87309-8 artesyn embedded technologies connector kit #70-841-020, includes all of the above. 1. specifcations subject to change without notice. 2. all dimensions in inches (mm), tolerance is 0.02 ( 0.5 mm) 3. mounting holes mh1 and mh2 should be grounded for emi purposes. 4. mounting hole mh1 is safety ground connection. 5. specifcations are for convection rating at factory settings at 115 vac input, 25 c unless otherwise stated. 6. this power supply requires mounting on metal standoffs 0.20 (5m) in height. 7. warranty: 2 years 8. weight: 0.75 lb/0.34 kg ordering information model number output voltage minimum load maximum load with convection cooling maximum load with 30cfm forced air peak load regulation 2 ripple p/p (pard) 3 lps202-m 5 v 0 a 20 a 40 a 44 a 2% 50 mv lps203-m 12 v 0 a 10.3 a 20.8 a 22 a 2% 120 mv lps204-m 15 v 0 a 8.3 a 16.6 a 18 a 2% 150 mv lps205-m 24 v 0 a 5.2 a 10.4 a 11.5 a 2% 240 mv LPS208-M 48 v 0 a 2.6 a 5.2 a 5.8 a 2% 480 mv 1. peak current lasting <30 seconds with a maximum 10% duty cycle. 2 . at 25 c including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . peak-to-peak with 20 mhz bandwidth and 10 f (tantalum capacitor) in parallel with a 0.1 f capacitor at rated line voltage and load ranges. 4. this product is a component power supply and is only for inclusion by professional installers within other equipment and must n ot be operated as a standalone product. emc compliance to appropriate standards must be verifed at the system level. this product is for sale to oems and system integrators, including through distribution channels. it is not intended for sale to end users. lps200-m series data sheet
lps200-m ds 28apr2016 mechanical drawing lps200-m series data sheet worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2016 artesyn embedded technologies, inc. all rights reserved. for full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com
|
